Dranetz Visa Guide de l'utilisateur Page 72
- Page / 274
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
4-10
Communications
Communications
Communication
interface setup
Communications Settings is where instrument-specific information is entered to allow
the PowerVisa to communicate to external devices using the optional Isolated
Communications
Module assemblies or modem (see related information on Chapter 9
Downloading Events).
Action... Result...
STEP 1: From the Instrument
Settings Setup Menu screen, press
Communications.
• Press Enable
Communications
to
activate/deactivate the
communications port. External
communication devices connect to
the PowerVisa mainframe via the
optical serial data port. The optical
serial data port connector is
located on the left side of the
instrument.
• Press to enter the communications
Device Address from 01 to 32 for
use with the optional Fiber Optic
to Ethernet adapter.
• Select the corresponding Baud
Rate to set connection speed.
Default baud rate is 11520.
• Press External Modem
Connected if you want to activate
communications via an external
modem. Press Change to modify
the modem initialization string.
The string must begin with “AT”.
Dranetz-BMI recommends using
the same brand and model of
modem at both ends of the
communications link. See Chapter
9 Downloading Events for
instructions on modem
connections.
• Press IP to configure your
Ethernet settings and allow the
PowerVisa to operate on the
network. Proceed to Step 2 on
page 4-11.
• Press OK to accept changes in
communications settings.
• Press Cancel to discard changes in
communications settings and
return to Instrument Settings
menu.
MARK159
NOTE: For instructions on how to physically
connect to NodeLink using the external
communications devices, see Chapter 9
Downloading Events.
- PowerVisa 1
- ADVERTENCIA 3
- WARNUNG 3
- Safety Summary 4
- Safety Summary, Continued 5
- Statements and Notices 7
- Continued 8
- Table of Contents 9
- Table of Contents, Continued 10
- Dranetz-BMI PowerVisa 13
- CHAPTER 1 15
- Getting Started 15
- Unpacking the PowerVisa 17
- Standard Accessories 18
- Top View 19
- Front View 19
- Rear View 19
- Bottom View 19
- 1 2 3 5 6 7 8 9 10 11 124 20
- CH 1/ Getting Started 21
- 2 3 5 64 22
- Rear view 23
- PowerVisa firmware 24
- PowerVisa Features 26
- Basic Operation 28
- PVISA001 29
- Basic Operation, continued 30
- CHAPTER 2 31
- PX5-11.vsd 35
- PX5-12.vsd 36
- PX5-13.vsd 37
- Connecting Current Probes 39
- 4300 TO LEMFLEX 40
- CURRENT PROBE 40
- ADAPTER CABLE 40
- 116310-G1 40
- PX5-14.vsd 40
- PX5-15.vsd 42
- CHAPTER 3 43
- View Real Time Data 43
- Turning Channels On/Off 45
- Checking Input Range 46
- Standard Meter Tab 48
- CH 3/ View Real Time Data 49
- Distortion Meter Tab 50
- Harmonic Graph 53
- Harmonic Detail 54
- Harmonic Options 55
- Harmonic Options, continued 56
- Harmonic List 57
- Phasor Screen 59
- Phasor Rotation 60
- CHAPTER 4 63
- Time and Date Settings 65
- Select Language 67
- Set Display Preferences 68
- Touch Screen Calibration 69
- Turn Threshold Beeper On/Off 71
- Data Card 74
- CH 4/ Instrument Settings 77
- CHAPTER 5 79
- Start Menu 79
- Current Probe Selection 86
- Scale Factor Setup 88
- Circuit Type Selection 90
- Nominal Values 92
- Nominal Values, continued 94
- Mode of Operation 95
- Monitoring Mode 96
- Advanced Options 97
- Site Name/Memory Card 98
- Action... Result 100
- CH 5/ Start Menu 101
- Section C 102
- Turning Monitoring On/Off 103
- Section D 112
- Section E 113
- Overview 113
- Card Error Messages 114
- CHAPTER 6 115
- Advanced Setup Options 115
- Advanced Options Menu 116
- Transient Limit 117
- RMS Variation Limit 122
- Waveform Capture 127
- Characterizer Options 128
- Journal Limit 129
- CH 6/ Advanced Setup Options 131
- 1 SEC, 1 MIN, 2 MINS 133
- 3 MINS, 5 MINS, 10 MINS 133
- 15 MINS, 1 HR 133
- 10%); Medium Voltage (11 135
- CHAPTER 7 137
- View Event Data 137
- Overview, continued 138
- Section A 140
- Event Data Display 141
- Event Activity Graph 142
- Event List 143
- Event Detail 145
- Event Options 150
- Section B 153
- Trend Display 154
- Trend Setup 155
- • Press OK to accept changes 156
- CH 7/ View Event Data 157
- CHAPTER 8 159
- Continued on next page 161
- EN50160 Compliance Limits 163
- CH 8/ Reports 165
- Compliance History 169
- Compliance History, continued 170
- Event Satistics 171
- Event Statistics, continued 172
- Panel Setup Options 175
- Panel Operation 177
- CHAPTER 9 181
- Downloading Events 181
- Communications 182
- CH 9/ Downloading Events 183
- Viewing Events via DranView 191
- DranView 192
- with HASP 192
- Top Side Bottom Side 193
- with HASP, continued 194
- APPENDIX A 195
- Optional Accessories 195
- Software Accessories List 202
- APPENDIX B 205
- Technical Specifications 205
- Interfaces 207
- Measured Parameters 208
- Computed Parameters 209
- WATTWATTWATTWATT ++= 211
- 61000-4-30 214
- TR2500 Current Probe 215
- TR2510 Current Probe 216
- APPENDIX C 217
- Battery Specifications 218
- AVERTISSEMENT 219
- Battery Pack Replacement 220
- Battery removal 221
- APPENDIX D 223
- User Replaceable Parts List 223
- APPENDIX E 225
- Common Circuit Connections 225
- Single Phase 231
- Split Phase 232
- 3 Phase, Four Wire Wye 233
- 3 Phase 2-Watt Delta 235
- Generic Circuit 236
- APPENDIX F 245
- Event Classification 245
- Variations as per 247
- IEEE, IEC, and 247
- Dranetz-BMI 247
- (continued) 247
- Range of 247
- APPENDIX G 249
- PowerVisa Menu Structure 249
- LEVEL 100/1 251
- Start Menu - Automatic Setup 251
- To Level 001 251
- To Level 108 252
- To Level 112 253
- LEVEL 100/2(b) 253
- Start Menu - Wizard Setup 253
- LEVEL 100/3a 254
- TO LEVEL 100/3b 254
- LEVEL 100/3b 255
- LEVEL 100/4 256
- LEVEL 100/5 256
- LEVEL 150 257
- Instrument Settings 257
- See Level 100/1 258
- To Level 200 258
- To Level 240 258
- LEVEL 200 259
- Scope Mode 259
- LEVEL 300/1 260
- Meter Mode - Standard 260
- LEVEL 300/2 261
- Meter Mode - Distortion 261
- 261
- LEVEL 240 263
- Phasor Display 263
- LEVEL 112_101 264
- Advanced Options 264
- LEVEL 112_201 265
- MARK112_207 266
- MARK112_208 266
- MARK112_214 266
- LEVEL 112_501 267
- Level 112_601 268
- Journal Interval 268
- LEVEL 112_701 269
- EN50160 Options 269
- Home screen 273
- LEVEL 470(b) 274
- Reports – PQ Status 274
Produits connexes et manuels pour Mesure, test et contrôle Dranetz Visa
(77 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.075 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels